- Conveyance of unit loads horizontally or at a slight upward gradient
- For continual material flow between machines and areas
Projects
Roller conveyor in restricted space with large range of parts
Project description
The restricted space situation and the large range of parts were the reason we realised a multi-track, double-decker roller conveyor with accumulation mode and extremely tight roller pitch (from 31 mm). It is based on the KRAUS RBA50 roller conveyor which has been specially adapted. A suitable sub-structure and the required control functions were part of the scope of supply. Our customer has been using it successfully for years for the production of larger gearboxes for tractors and trucks.
Customer/branch: Mechanical engineers, automotive suppliers
Flat pallet supply roller conveyor in tandem design
Project description
A flat pallet supply roller conveyor in tandem design for extra-long manual pallet trucks with 2 Euro pallets was realised for an equipment manufacturer.
The specification was to supply Euro pallets to a roller conveyor by pallet truck. The design height was reduced to 80 mm. The customer integrated the drive in the lift table pit to prevent it projecting above the roller conveyor.
Customer/branch: Equipment manufacturer
Products
Roller conveyor RBA 50
Frame structure
Sheet steel profile (wall thickness 3 mm) with welded cross braces
Chain guard cover closed completely
Dimensions
Chain case: 120 x 60 x 3 mm
L-profile: 80 x 40 x 3 mm
Roller spacing: adapted depending on load
Conveyor rollers
Kraus conveyor rollers series 5020
Galvanised steel tube Ø 50 mm x 1.5 mm
Steel axle Ø 12 mm with internal thread M8x15, with double chain wheel, steel: 1/2" x 5/16", number of teeth = 14
Drive
Chain drive with three-phase gear motor 230/400 V – 50 Hz, IP55
The conveyor rollers are driven by a 1/2" x 5/16" chain from roller to roller Motor position: in the centre under the frame structure
Conveying speed: Standard speed 6–30 m/min
Conveyor width
The width is determined by the properties and weight of the unit load – the unit load should be resting on at least 3 rollers
Standard widths: 470 mm, 670 mm, 870 mm
Conveyor length: on request, depending on the roller spacing
Surface finish
Painted in RAL colours/galvanised
Advantages
Conveyance of unit loads horizontally or at a slight upward gradient
No downward gradient required
Sturdy design
Very good transmission of force
Safe to use thanks to chain guard cover
Low-noise running
Roller conveyor RBA 50 tangential
Frame structure
Sheet steel profile (wall thickness 3 mm) with welded cross braces
Chain guard cover closed completely
Dimensions
Chain case: 120 x 60 x 3 mm
L-profile: 80 x 40 x 3 mm
Roller spacing: adapted depending on load
Conveyor rollers
Kraus conveyor rollers series 5020
Galvanised steel tube Ø 50 mm x 1.5 mm
Steel axle Ø 12 mm with internal thread M8x15, with double chain wheel, steel: 1/2" x 5/16", number of teeth = 14
Drive
Chain drive with three-phase gear motor 230/400 V – 50 Hz, IP55
The conveyor rollers are driven by a 1/2" x 5/16" chain from roller to roller Motor position: in the centre under the frame structure
Conveying speed: Standard speed 6–30 m/min
Conveyor width
The width is determined by the properties and weight of the unit load – the unit load should be resting on at least 3 rollers
Standard widths: 470 mm, 670 mm, 870 mm
Conveyor length: on request, depending on the roller spacing
Surface finish
Painted in RAL colours/galvanised
Advantages
Conveyance of unit loads horizontally or at a slight upward gradient
No downward gradient required
Sturdy design
Very good transmission of force
Safe to use thanks to chain guard cover
Low-noise running
Roller conveyor RBA 80/89
Frame structure
Sheet steel profile (wall thickness 5 mm) with welded cross braces
Chain guard cover closed completely
Dimensions
Chain case: 150 x 70 x 5 mm
L-profile: 100 x 50 x 5 mm
Roller spacing: adapted depending on load
Conveyor rollers
Kraus conveyor rollers series 5105
Galvanised steel tube Ø 80 mm x 2 mm / Ø 89 mm x 3 mm
Steel axle Ø 20 mm with internal thread M10x20, with double chain wheel, steel: 5/8" x 3/8", number of teeth = 15
Drive
Chain drive with three-phase gear motor 230/400 V – 50 Hz, IP55
The conveyor rollers are driven by a 5/8" x 3/8" chain from roller to roller
Motor position: in the direction of transport, in the centre under the frame structure
Standard transport speed: 6–30 m/min
Conveyor width: the width is determined by the properties and weight of the unit load – the unit load should be resting on at least 3 rollers
Standard belt widths: 985 mm, 1185 mm
Conveyor length: on request, depending on the roller spacing
Surface finish
Painted in RAL colours/galvanised
Advantages
Conveyance of pallets, skeleton containers, boards and barrels
Sturdy design
Very good transmission of force
Safe to use thanks to chain guard cover
Low-noise running
Conveyance of unit loads horizontally or at a slight upward gradient
Round belt conveyors
Frame structure
Steel C-profile, galvanised, with bolted cross braces
Frame dimensions: 100 mm x 30 mm x 2 mm
Min. roller spacing: 25 mm
Conveyor rollers
Kraus conveyor rollers series 3760 (bead roller)
Galvanised steel tube Ø 50 mm x 1.5 mm
Steel axle Ø 12 mm with internal thread M8x15, with single or double bead
Drive
Drive with three-phase gear motor 230/400 V – 50 Hz, IP55
The conveyor rollers are driven by a vertical shaft underneath via round belts Ø 5 mm.
Motor position: in the centre under the frame structure
Standard transport speed: 6–24 m/min
Conveyor width
The width is determined by the properties and weight of the unit load – the unit load should be resting on at least 3 rollers
Standard conveyor widths: 470 mm, 670 mm, 870 mm
Standard conveyor lengths: 1000 mm, 2000 mm, 3000 mm
Design height
105 mm (bottom of side profile to top edge of conveyor roller, without chain guard cover, without drive unit)
Surface finish
Painted in RAL colours/galvanised
Advantages
Suitable for accumulation
Easy to combine
mit Standardrollenbahnen
sehr einfaches Funktionsprinzip
wartungs- und revisionsfrei
geräuscharmer Lauf
Accumulation roller conveyors
Frame structure
Sheet steel profile (wall thickness 3 mm) with welded cross braces
Chain guard cover closed completely
Dimensions
Chain case: 120 mm x 60 mm x 3 mm
L-profile: 80 mm x 40 mm x 3 mm
Roller spacing: adapted depending on load
Conveyor rollers
Kraus conveyor rollers series 5020 accumulation drive
Galvanised steel tube Ø 50 mm x 1.5 mm
Steel axle Ø 12 mm with internal thread M8x15, with double chain wheel, steel or PVC: 1/2" x 5/16", number of teeth = 14
Drive
Chain drive with three-phase gear motor 230/400 V – 50 Hz
The conveyor rollers are driven by a 1/2" x 5/16" chain from roller to roller.
The force is transmitted to the tube by means of the slip coupling.
Motor position: in the centre under the frame structure
Standard transport speed: 6-24 m/min
Conveyor width
The width is determined by the properties and weight of the unit load – the unit load should be resting on at least 3 rollers
Standard widths: 470 mm, 670 mm, 870 mm
Standard conveyor lengths: 1905 mm, 3048 mm, 3810 mm, 4953 mm, 5715 mm
Surface finish
Painted in RAL colours/galvanised
Advantages
Transport without accumulation pressure
Sturdy design
Safe to use thanks to chain guard cover
Low-noise running
Mini tapered conveyor roller curves, power-driven
Frame structure
Frame comprising of rolled-up flat steel with welded cross-bars
Frame height 70 mm
Wall thickness 3 mm
Conveyor rollers
Kraus conveyor rollers series 0600
Steel tube Ø 20 mm x 1.5 mm with plastic tapered elements slid in place, with double chain wheel, steel 6 x 2.8 mm, number of teeth = 17, Steel axle Ø 8 mm with internal thread M5
Drive
Chain drive from roller to roller
Three-phase gear motor 230/400 V – 50 Hz, IP55
Motor position: in the direction of transport, in the centre under the frame structure
Standard conveyor widths
240 mm, 340 mm, 440 mm, 540 mm
Inner radius
360 mm
Surface finish
Painted in RAL colours/galvanised
Advantages
Extremely versatile
Quiet, safe to use and low-maintenance
Simple assembly
Precise curve guidance and high degree of working safety
Tapered conveyor roller curves, power-driven
Frame structure
Frame comprising rolled-up flat steel with welded cross-bars
Frame height 100 mm
Wall thickness 3 mm
Conveyor rollers
Kraus conveyor rollers series 3700
Steel tube Ø 50 mm x 1.5 mm with plastic tapered elements slid in place, with double chain wheel, steel 1/2" x 5/16", number of teeth = 14
Steel axle Ø 14 mm with internal thread M10
Drive
Chain drive from roller to roller
Three-phase gear motor 230/400 V – 50 Hz, IP55
Motor position: in the direction of transport, in the centre under the frame structure
Standard conveyor widths
470 mm, 670 mm, 870 mm, 1070 mm
Inner radius
900 mm
Surface finish
Painted in RAL colours/galvanised
Advantages
Extremely versatile
Quiet, safe to use and low-maintenance
Simple assembly
Precise curve guidance and high degree of working safety
Accordion roller conveyors, power-driven
Frame structure
Accordion connection galvanised steel with stabilizers
Conveyor width
Conveyor widths: 400 mm, 500 mm, 600 mm
Conveyor length
maximum extended length achievable: 7,500 mm
Height adjustment: stepless from 720 to 1,150 mm
Drive
Round belt drive from roller to roller
Small motors 24V
Motor position: in the direction of transport, in the centre under the frame structure
Incl. reversing switch for reverse operation
Advantages
Versatile use: for constantly changing locations and variable conveyor routes, as buffer or run-out track
Simple extension to a conveyor with manual and gravity drive
Curve designs of 180° possible
Low space requirement
Our customers
